This product can no longer be ordered.
Production is discontinued.
GSM-SP10B is industrial SMS processor for remote controling and monitoring using GSM network.
— 9 digital inputs
— 1 analogue input ( 0-20mA, 0-10V, KTY, Pt100, Pt1000 )
— 8 digital outputs
— Li-ION battery
— power supply 8-30Vss
- Select accessories
- Product description
- Technical specification
- Commercial packaging
GSM-SP10B is a powerful remote control and monitoring device. It enables to monitor digital and analog inputs status and to control outputs via GSM network. SP10 can use SMS messages, GPRS connection. The behavior of a device and names of inputs and outputs are in SMS version fully selectable via USB cable or remotely (GPRS) using supplied configuration software. The defined emergency conditions may result in sending a SMS message to the list of telephone numbers (boiler failure, gas leakage, rapid drop or rise of temperature or level) including information about the failure and restoration of power supply.
connector for MODBUS or GSM-SP-EXP
dimensions W x H x D [mm]
MC price w/o VAT
|VC price w/o VAT|
|GSM-SP10||9DIn, 1AIn, 8DOut||YES||YES||60x90x80 60x90x53*2)||see Support||Call and ask||Call and ask|
|GSM-SP10B||9DIn, 1AIn, 8DOut||NO *1)||YES||60x90x8060x90x53*2)||see Support||Call and ask||Call and ask|
*1) The licence for SD card and logging software can be bought additionally.
*2) It’s possible to rebuild the box for a certain fee.
- Simple installation – The device is delivered with a frame for mounting onto DIN rail.
- Easy monitoring – just send a SMS message “1234 STATE“ to receive a message about the state of the device inputs and outputs.
- Configuration and Monitoring SW – user friendly PC SW works either locally via USB port or remotely using GPRS.
- Backup power – backup Li-ION battery enables alert on 230 VAC failure.
- Boiler houses, heating plants and heat pumps.
- Industrial objects – water plants, water reservoirs, small hydroelectric stations, boiler plants.
- Technology processes – fault report, gas leakage, drop or rise of temperature or level, freezing point monitoring.
For configuration of GSM-SP10 is used sw SeaConfigurator (full version can be downloaded for free in the section support).
If you need more inputs, it is possible to connect expansion module GSM-SP-EXP to SP10. This expansion module has 9 digital inputs and 7 analog inputs. GSM-SP-EXP is connected to GSM-SP10 via the flat strip cable, from which is the unit powered.
Communication boards ( MODBUS RTU, MODBUS ASCII, FATEK PROTOCOL )
The SP10 is possible to connect the communications board. This is an expansion board serial port for SP10. Used for connecting to control systems (PLC, PC) that can create so-called. Numbered events. GSM-SP10 can be both MASTER and SLAVE. Serial port expansion board plugs into the 8-pin dual row connector located under the front bezel. Choose between two variations of GSM-SP-CB2 is a RS232 serial port and GSM-SP-CB5 the RS485 serial port with switchable terminator. The communication method and choice of registers is set using SeaConfigurator on the General tab.
|Power supply||8 – 30 Vss (max. 0,5 A at 12 VDC, average consumption 0,66 W)|
|AKU||Built-in rechargeable Li-Ion battery|
|Digital inputs||9 inputs for voltage 8 – 30 VDC; galvanically separated; one common terminal|
|Analog inputs||1 software switchable input (0 – 20 mA, 0 – 10 V, KTY, Pt100, Pt1000)|
|Digital outputs||8 outputs (100 mA/50 VDC or 70 mA/35 VAC); galvanically separated|
|Ports||USB 2.0 for configuration and monitoring|
in case of interest, it is possible to install the module 850/900/1800/1900 MHz
|Operating temperature||-20 to +45°C|
|Dimensions||width 60 mm x height 90 mm x depth 80 mm / (53 mm) **)|
( height without GSM antenna, depth from DIN rail )
*) See the manual for technical details.
**) It’s possible to exchange the box for a certain fee.